Login  |  Register
Infinitihelp.com - All About Infiniti
Do-It-Yourself Maintenance Owners Manuals Recalls/Campaigns Service Bulletins Service Manuals Infiniti OBDII Codes Glossary & Acronyms More...
Member's Ride Photos Stock Photo Gallery
Classifieds - For Sale Classifieds - Wanted To Buy Classifieds - Mechanic Wanted Classifieds - Auto Services
Register FAQ Social Groups Mark Forums Read
Forums > > > 2007 M
Forgot Password? Join Us!


2.3.0

2007 M
2007 Infiniti M35 / M45 Service Bulletins
New entries announced in forum Latest Uploads
Allowances: 0 files/0 used

Keyword Filter
  
Sort by

  Entries Show full/short entries
Access denied ITB17-042a
-REVISED-
VARIOUS INFINITI MODELS; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING
The MIL is ON in an APPLIED VEHICLE with DTC P0456 (EVAP VERY SML LEAK)
AND
  • DTC P0456 is not caused by a loose fuel fill cap (refer to ITB13-044).
  • An EVAP leak has been detected where the vent control valve mounts to the canister.
  • The vent control valve O-ring seal is determined to be the cause.

Discussion Thread
 
Send to Friend Suggest other entries I might like
08-22-2017
1.74 Mbytes Hits 18
Keywords: control dtc p0456 valve vent
Access denied ITB17-026
VARIOUS INFINITI MODLES; INFINITI; FUEL TANK IS SLOW OR DIFFICULT TO FILL
The fuel tank is slow or difficult to fill (filling nozzle shuts off before tank is full).

Discussion Thread
 
Send to Friend Suggest other entries I might like
03-20-2017
660.28 Kbytes Hits 86
Keywords: slow tank fuel fill
Access denied ITB17-018
VARIOUS INFINITI MODELS; BALL JOINT AXIAL END PLAY PROCEDURE
When working on the front suspension, use the updated service information in this bulletin along with the Electronic Service Manual (ESM).

Discussion Thread
 
Send to Friend Suggest other entries I might like
03-07-2017
678.82 Kbytes Hits 55
Keywords: ball joint axial end play
Access denied ITB16-005
VARIOUS INFINITI MODELS; INFINITI INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES
The Intelligent Keys used on the various Infiniti vehicles may not be interchangeable between models and years.

Discussion Thread
 
Send to Friend Suggest other entries I might like
01-06-2016
184.59 Kbytes Hits 33
Keywords: swapping or replacement
Access denied ITB15-025
ALL INFINITI MODELS; SERVICING RUN FLAT TIRES AND LOW PROFILE TIRES EQUIPPED WITH TPMS SENSORS
When servicing run flat tires or low profile tires:
  • Special equipment and procedures are required to avoid damage.
  • Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires.
  • TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty.
  • To avoid such damage, ensure that the tire changer being used and the operator of the tire changer are capable of servicing run flat and low profile tires.
  • Operator’s manuals for such tire changers must be followed.

Discussion Thread
 
Send to Friend Suggest other entries I might like
07-07-2015
1.62 Mbytes Hits 44
Keywords: flat sensors tires tpms run
Access denied ITB15-024
2005-2015 ALL INFINITI MODELS; ECM REPROGRAMMING SERVICE INFORMATION
After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming.

Discussion Thread
 
Send to Friend Suggest other entries I might like
06-25-2015
81.24 Kbytes Hits 60
Keywords: ecm reprogramming
Access denied ITB15-020
VARIOUS INFINITI MODELS; PRECAUTIONS FOR CLEANING PAINTED ALLOY WHEELS
The appearance of painted alloy wheels can be damaged if acidic cleaners are used

Discussion Thread
 
Send to Friend Suggest other entries I might like
05-08-2015
365.18 Kbytes Hits 59
Keywords: alloy wheels cleaning painted
Access denied ITB15-019
VARIOUS INFINITI MODLES; CONFIGURATION FOR BLANK REPLACEMENT BCM
The Body Control Module (BCM) for the Applied Vehicles above is now shipped as a “blank” unit.

Discussion Thread
 
Send to Friend Suggest other entries I might like
05-01-2015
255.42 Kbytes Hits 19
Keywords: bcm blank replacement
Access denied ITB14-055
ALL INFINITI MODELS; DIAGNOSIS OF POOR ACCELERATION OR LACK OF POWER
If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair.

Discussion Thread
 
Send to Friend Suggest other entries I might like
11-21-2014
82.98 Kbytes Hits 401
Keywords: acceleration power lack
Access denied ITB14-028
ALL INFINITI MODELS; FLUID LEAK REPAIR SERVICE INFORMATION
The following information is provided to help ensure correct diagnosis and repair of fluid leaks. All fluid leaks, when properly diagnosed, should be repaired (whether under warranty or customer pay) to ensure proper vehicle operation.

Discussion Thread
 
Send to Friend Suggest other entries I might like
06-24-2014
2.14 Mbytes Hits 77
Keywords: fluid leak repair
 


 
CarZone Auto | Nissan and Infiniti Service Center

 

All times are GMT. The time now is 02:12 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2018, vBulletin Solutions Inc.
Search Engine Optimisation provided by DragonByte SEO v2.0.37 (Lite) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.